PACKAGE SPECS AT-A-GLANCE
SHELL COMPONENTS

NOTE: First floor system by Builder per plans
Joists, beams, headers and girders
2” X 10” SPF #2/Btr. (shipped loose)
19% maximum moisture content
Meets or exceeds requirements:  NLGA grading rule; ALS approved
16” open web floor trusses included for the “Low Country” models

3/4" x 4’ x 8’ tongue & groove OSB with construction adhesive (shipped loose)

Meets or exceeds requirements of NER 108 HUD/FHA TECO

Lancaster Redevelopment Corporation pre-assembled trusses - 6/12 pitch typical or per individual plan

Trusses typically 24" o.c. per design drawings (16" overhang at eaves)

30 PSF live load

Alpine truss plates

Truss plates - 20 ga.

Meets or exceeds requirements of FHA and IRC 2006 codes

Note:  All Cape Cod styles are a pre-cut rafter system

2 x 6 SPF #2 fascia board

 7/16" OSB 4x8 NER-108 rating

Aluminum H-clips provided for use between centers

Meets or exceeds requirements of HUD/FHA TECO

Shingles-Tamko Heritage architectural – 30-year warranty

Tamco hip and ridge supplied for shingle cap

Shingles Class “A" type 1 12" x 37" with 5" exposure

Meets or exceeds requirements of ASTM - D 3462-83 and D-3018-82

U.L. approved

Fed. spec SS-S-001534

Underlay-Felt shingle underlayment #15 Grade   36"x 144' roll (covers 432 sq. ft.)

Meets or exceeds requirements of U.L. approval - prepared roofing necessary

Air vent - rolled shingle over

Drip edge - all sides

 Single-hung tilt vinyl windows or vinyl casements per plan

 Meets or exceeds requirements of ASHRAE codes

 Bottom sashes are operable

Half Screen’s included throughout

Casement (on certain models per plan)

Fixed glass panel (on certain models) trapezoidal or transom

Integral J channel where applicable

Factory assembled “Quick-Trim” (2 ¼ “ casing, apron, jamb & sill in a single assembly)

Factory applied Vycor Plus self-adhered flashing to header’s, sill’s and jamb’s

Grilles are available as an option

One designated  window per plan will be factory installed with screws to allow for drywall stocking.

Therma-Tru or Benchmark polystyrene core-insulated steel clad six panel entry door or per plan (location per prints

Therma-Tru or Benchmark polystyrene core-insulated steel clad #263 sidelights (main entry door only, per prints)

Thermal break construction

Thermal break aluminum threshold

Compression weather-stripping

Composite sill

Prime painted

Solid lock block 25 ga. steel

Thermal transmission R Value 7.22

Vycor Plus self-adhered flashing for head’s, jamb’s and threshold’s (shipped loose)

Therma-Tru Single Active Steel Swing Patio Door or Capital Vinyl Sliding Glass Door as per individual plan.

2 1/2" surface applied stone (per individual model)

Galvanized wire lath shipped loose

Corner stones, electrical box stones, windowsill stones, shutter block stones, soldier stones, and (as required per individual model)

Norandex or equivalent vinyl soffit-fully vented except cantilever overhangs, gable overhangs, porch ceilings ¼ vented, ¾ solid

Aluminum fascia

Vinyl F channel & J channel accessories

Mid-America light fixture blocks - match siding, color

Meets or exceeds HUD minimum requirements and AAMA standards

Starter strips & undersill trim

Choice of colors

Exposed rafter tail assembly where shown on “Low Country” models

15" wide 1 1/8" thick

One piece construction wood grain texture

Open louver - raised panel shutters available as option

Front elevation only (per individual plan)

PRODUCTS AND MANUFACTURERS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
A DETAILED SPECIFICATION SHEET IS AVAILABLE UPON REQUEST.